Sediment control products description. Here’s where will put a short description on these types of products and their typical use scenarios and such…

ALL PRODUCTS

  • Pre-Fabricated Silt Fence

    Pre-Fabricated Silt Fence

    Pre-fabricated Silt Fence consists of 36” woven geotextile fabric attached to 48” wooden post. 100 linear feet per roll.
    A silt fence is a temporary barrier designed to retain sediment on the construction site. it consists of posts supporting and attached to a geotextile that is trenched in to the ground. The fence retains sediment primarily be retarding flow and promoting deposition of the sediment on the uphill side of the fence. Runoff is also filtered as it passes through the geotextile.
    Silt Fences are intended to intercept and detain small amounts of sediment from disturbed areas.
    The use of silt fence as a sediment barrier is not recommended in areas of concentrated flow such as in high flow ditches. In those cases filter berms, silt dikes and excelsior wattles or rock check dams should be used.
    Category:
    Read more
  • Silt Saver – D.O.T Filter

    Silt Saver – D.O.T Filter

    The D.O.T Filter is designed with the fitted polyester filter fabric extending half way up the HDPE domed frame. The more permeable, high view green fabric covers the rest of the dome for greater flow capabilities.
    Available for the 60” round or square Silt Saver Inlet Protection Devices
    Category:
    Read more
  • Silt Saver – High Flow Filter

    Silt Saver – High Flow Filter

    The High Flow Filter is designed with the high view green fabric covering the entire frame. The more permeable fabric allows for greater flow through the system while still maintaining the ability to filter storm water runoff.
    Available for the 60” round or square Silt Saver Inlet Protection Devices
    Category:
    Read more
  • SS-100A

    SS-100A

    Silt Saver Inlet Protection

    SS-100A Round Frame & Filter Assembly

    SS-100A Silt Saver frame & Filter are designed to fit most round 60” O.D. pre-cast risers used in residential and light commercial applications.

    The filter is designed to custom fit each frame and is constructed of non woven polyester, with a fill pocket at the bottom that can be filled with soil, rock, or sand.

    Silt Saver Frame and Filter assembly will also accommodate drainage structures smaller than these listed with no special design required.

    SS-100A Spec Sheet

    Applications: Inlet Protection, Safety Guard

    Category:
    Read more
  • SS-200A Square Base Frame & Filter Assembly

    SS-200A Square Base Frame & Filter Assembly

    SS-200A Square Base Frame & Filter Assembly

    SS-200A Silt Saver frame & Filter are designed to fit most square 60” O.D. brick or pre-cast risers used in most DOT highway applications.

    The filter is designed to custom fit each frame and is constructed of non woven polyester, with a fill pocket at the bottom that can be filled with soil, rock, or sand.

    Silt Saver Frame and Filter assembly will also accommodate drainage structures smaller than these listed with no special design required.

    SS-200A Spec Sheet

    Applications: Inlet Protection, Safety Guard

    Category:
    Read more
  • Triangular Silt Dike

    Triangular Silt Dike

    Triangular Silt Dike is designed as an economical alternative to silt fence, straw wattles, and sand bags. They are lightweight, durable, re-usable, and easily installed.

    Standard Unit Specifications
    Height 10” / Length 7’

    Read more
  • Turbidity Barrier

    Turbidity Barrier

    There are three types of barriers to choose from. The barrier you need for your application depends soil composition, site conditions, and current velocity. The success of the barrier depends on this barrier selection, installation, and maintenance.
    Standard Roll Specifications
    Height 5-10’ / Length 50’
    Other sizes are available upon request.
    Applications: Floating turbidity barriers are designed to contain movement of the flow of silt laden runoff from a construction site keep it contained in a limited area and allow the silt and sediment to settle out
    Category:
    Read more
  • Type “A” Alternate Silt Fence

    Type “A” Alternate Silt Fence

    Type “A” Alternate Silt Fence consists of 5’ steel T post, 32” hog wire, 42” woven geotextile fabric, clips and rings for fastening. 330 linear feet per kit.
    A silt fence is a temporary barrier designed to retain sediment on the construction site. it consists of posts supporting and attached to a geotextile that is trenched in to the ground. The fence retains sediment primarily be retarding flow and promoting deposition of the sediment on the uphill side of the fence. Runoff is also filtered as it passes through the geotextile.
    Silt Fences are intended to intercept and detain small amounts of sediment from disturbed areas.
    The use of silt fence as a sediment barrier is not recommended in areas of concentrated flow such as in high flow ditches. In those cases filter berms, silt dikes and excelsior wattles or rock check dams should be used.
    Category:
    Read more
  • Type “A” Silt Fence

    Type “A” Silt Fence

    Type “A” Silt Fence consists of 5’ steel T post, 39” supporting wire, 48”non-woven geotextile fabric, clips and rings for fastening. 330 linear feet per kit.
    A silt fence is a temporary barrier designed to retain sediment on the construction site.  The fence retains sediment primarily be retarding flow and promoting deposition of the sediment on the uphill side of the fence. Runoff is also filtered as it passes through the geotextile.
    Silt Fences are intended to intercept and detain small amounts of sediment from disturbed areas.
    The use of silt fence as a sediment barrier is not recommended in areas of concentrated flow such as in high flow ditches. In those cases filter berms, silt dikes and excelsior wattles or rock check dams should be used.
    Category:
    Read more

Showing all 9 results